print date 05/09/07 15 th , aug, 05 multilayer ceramic antenna for 433 mhz (small size) can4313 129 200431b 30 th , aug,05 7 th , sep,05 dennis liu c.t.lee 7 th ,sep, 05 page 1 sheet 190-1 a4 spec.doc wide band multilayer ceramic antenna for 850~950mhz product specification quick reference data size 16.5*14*0.9 mm working frequency 850~950mhz gain 1.5 dbi max vswr 2 max polarization linear azimuth omni-directional impedance 50 operating temperature -55~85 o c termination ni/sn (environmentally-friendly leadless) resistance to soldering heats 260 o c, 10 sec. special environmental concerns- green products design: the foil making process is using environmentally friendly aqueous solvent technology. termination is lead free and packing materials can be re-cycled 433mhz ceramic chip antenna antenna products sep, 2005, v3
print date 05/09/07 15 th , aug, 05 multilayer ceramic antenna for 433 mhz (small size) can4313 129 200431b 30 th , aug,05 7 th , sep,05 dennis liu c.t.lee 7 th ,sep, 05 page 2 sheet 190-2 a4 spec.doc multilayer ceramic antenna (linear polarization mode) for 400mhz~500mhz product specification 1 quick reference data __________________________________________________________________________ working frequency* 400~500mhz bandwidth 20 mhz (min) gain 0.5 dbi (max) vswr 3.0 max polarization linear azimuth omni-directional impedance 50 operating temperature -40~85 o c termination ni/sn (environmentally-friendly leadless) resistance to soldering heat 260 o c, 10 sec. special environmental concerns- green products design: the foil making process is using environmentally friendly aqueous solvent technology. termination is lead free and packing materials can be re-cycled 1. application 1 all the technical data and information contained herein are subject to change without prior notice
print date 05/09/07 15 th , aug, 05 multilayer ceramic antenna for 433 mhz (small size) can4313 129 200431b 30 th , aug,05 7 th , sep,05 dennis liu c.t.lee 7 th ,sep, 05 page 3 sheet 190-3 a4 spec.doc 60 mm back side back side all ground plan ( but under antenna should avoid ground ) plane ) cleanness circuits space rf- module 40 50 ohm transmission line top side
print date 05/09/07 15 th , aug, 05 multilayer ceramic antenna for 433 mhz (small size) can4313 129 200431b 30 th , aug,05 7 th , sep,05 dennis liu c.t.lee 7 th ,sep, 05 page 4 sheet 190-4 a4 spec.doc 2. solder land pattern for antenna figure dimensions remark w f 0.85 0.3 mm 4.20 0.3 mm feed pad feed pad 1 w f
print date 05/09/07 15 th , aug, 05 multilayer ceramic antenna for 433 mhz (small size) can4313 129 200431b 30 th , aug,05 7 th , sep,05 dennis liu c.t.lee 7 th ,sep, 05 page 5 sheet 190-5 a4 spec.doc 3. mechanical data figure dimension port w l t 4 0.5mm 12 0.5mm 1.5 0.3mm feed termination solder termination 4. test board dimension for s11 (return loss) and radiation pattern measurnment fr-4 pcb thickness = 0.8 mm the length of transmission line = 60 mm ( depends on pcb thickness) 60 mm 40 50 ohm transmission 1 l w t
print date 05/09/07 15 th , aug, 05 multilayer ceramic antenna for 433 mhz (small size) can4313 129 200431b 30 th , aug,05 7 th , sep,05 dennis liu c.t.lee 7 th ,sep, 05 page 6 sheet 190-6 a4 spec.doc 5. s11 return loss
print date 05/09/07 15 th , aug, 05 multilayer ceramic antenna for 433 mhz (small size) can4313 129 200431b 30 th , aug,05 7 th , sep,05 dennis liu c.t.lee 7 th ,sep, 05 page 7 sheet 190-7 a4 spec.doc reliability data (reference to iec specification) iec 384-10/ cecc 32 100 clause iec 6006868-2 test method test procedure requirements 4.4 mounting the antenna can be mounted on printed- circuit boards or ceramic substrates by applying wave soldering, reflow soldering (including vapour phase soldering) or conductive adhesive no visible damage 4.5 visual inspection and dimension check any applicable method using 10 magnification in accordance with specification (no chip off 3 mm) 4.6.1 antenna central frequency at 20 o c standard test board in page 4 4.8 adhesion a force of 5 n applied for 10 s to the line joining the terminations and in a plane parallel to the substrate no visible damage 4.9 bond strength of plating on end face mounted in accordance with cecc 32 100, paragraph 4.4 no visible damage conditions: bending 0.25 mm at a rate of 1mm/s, radius jig. 340 mm,1 mm warp on fr4 board of 90 mm length no visible damage
print date 05/09/07 15 th , aug, 05 multilayer ceramic antenna for 433 mhz (small size) can4313 129 200431b 30 th , aug,05 7 th , sep,05 dennis liu c.t.lee 7 th ,sep, 05 page 8 sheet 190-8 a4 spec.doc iec 384-10/ cecc 32 100 clause iec 6006868-2 test method test procedure requirements 4.10 tb resistance to soldering heat 260 5 c for 10 0.5 s in a static solder bath the terminations shall be well tinned after recovery and central freq. change 6% resistance to leaching 260 5 c for 30 1 s in a static solder bath using visual enlargement of 10, dissolution of the termination shall not exceed 10% 4.11 ta solderability zero hour test, and test after storage (20 to 24 months) in original atmosphere; un-mounted chips completely immersed for 2 0.5 s in 235 5 c. the termination must be well tinned, at least 75% is well tinned at termination
print date 05/09/07 15 th , aug, 05 multilayer ceramic antenna for 433 mhz (small size) can4313 129 200431b 30 th , aug,05 7 th , sep,05 dennis liu c.t.lee 7 th ,sep, 05 page 9 sheet 190-9 a4 spec.doc ordering information: the antenna may be ordered by using the ordering code. these code numbers can be determined by the following rules: can43 13 1 29 20 043 1b f c m s t a t f. family code can43 = antenna c. packing type code 13 = bulk m. materials code 1 = high frequency material s. size code 29 = 12* 4 * 1.5 mm t. tolerance 20 = 20m hz band width a. working frequency 043 = 400~500mhz can4311129200431b (clear text code example) can43 13 1 29 20 043 1 b product packing type material size type working frequency quantities packing can43= antenna bulk ltcc material 29=12*4mm 20= 20mhz 043=433mhz 1= 1k pcs bulking packing
print date 05/09/07 15 th , aug, 05 multilayer ceramic antenna for 433 mhz (small size) can4313 129 200431b 30 th , aug,05 7 th , sep,05 dennis liu c.t.lee 7 th ,sep, 05 page 10 sheet 190-10 a4 spec.doc revision control: revision date content remark 1 15 th , aug. 2005 new issued 2 30 th , aug. 2005 modification of end-termination s appearance 3 7 th , sep. 2005 modification of 12nc and packing type
|
